Showing results: 346 - 360 of 473 items found.
-
Optical Zonu Corp.
Optical Zonu’s RF over Fiber product line contains multiple stand-alone modules which are designed to integrate easily with your application. Each of our stand-alone modules is a Transceiver (TRx), but it may also be configured as individual Transmitter (Tx) or Receiver (Rx) units. A pair of these transceivers creates two-way bidirectional RF to Optical and Optical to RF link. Standard operational frequency ranges between 47 MHz and 3 GHz but can be extended to from 10 KHz to 3.3 GHz. OZ816 and OZ1606 modules have ultra-broadband capability that ranges from 47MHz to 7 GHz.
-
Extech PM120 -
Extech Instruments Corporation
Monitor and record power usage of home and work appliances for energy conservation and cost reduction analysis with the Extech PM120 Power Monitor. This helps you determine if the electrical device should be replaced with a higher efficiency unit. The PM120 has a large dual LCD. The primary display shows voltage, current, power, power factor, and frequency readings. The secondary display shows total time, cost (cost of operation per minute, day, or week), set, or energy. Design includes a standard, North American 3 prong plug, front socket connection, and backup battery that saves customized programs.
-
2940A -
Novatech Instruments , Inc.
The 2940A is a two-channel 400MHz DDS Signal Generator that generates two independent sine wave output frequencies simultaneously from 200kHz to 400MHz in 1Hz steps. A Clock Generator configuration with ECL or LVDS clock outputs is also available. The 2940A is lockable to an external frequency standard or is used with its internal TCXO. Optional internal amplifiers and 60dB step attentators available. Set all parameters with front panel controls and LCD display or by computer using the RS232 serial interface. All settings can be saved into non-volatile EEPROM memory upon power down. Windows software included.
-
MPI-520S -
Sonel S.A.
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
-
779079-04 -
NI
2.7 GHz, Digital Upconverter Included, PXI Vector Signal Generator—The PXI‑5671 features quadrature digital upconversion, which reduces waveform download and signal generation time. It is a general-purpose vector signal generator that can generate standard modulation formats such as AM, FM, PM, ASK, FSK, MSK, GMSK, PSK, QPSK, PAM, and QAM. The PXIe‑5671 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as emerging areas including software-defined radio, radio frequency identification (RFID), and wireless sensor networks. For specific communications standards, you can use various software add-ons to generate modulated signals according to standards such as WCDMA, DVB‑H, and ZigBee
-
RFCT -
Textron Systems
Textron Systems’ Radio Frequency Cable Tester (RFCT) allows for on-site testing and maintenance for radio frequency (RF) transmission paths within a platform. Using preconfigured databases of sweep parameters and pass/fail criteria, the RFCT quickly determines the status of installed RF cables. The RFCT checks each cable’s performance characteristics to include voltage standing wave ratio (VSWR), insertion loss (IL), phase and phase matching. If a cable fails a test, the RFCT automatically determines the distance-to-fault (DTF). With its intuitive touchscreen-based user interface and lightweight, ruggedized packaging, the RFCT is the gold standard for operational-level RF cable testing.
-
MC142 -
Powertek LLC
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using signals with various crest factors. Frequency modes enable selection of frequency, amplitude and duty cycle of the output signal. These are suitable for basic calibration of digital and analog oscilloscopes along with transient recorders. The calibrator is equipped to measure temperature with TC and RTD temperature sensors. Its built-in multimeter can be used independently or simultaneously with the calibrator output. Testing of transducers of various types, regulators and sensors can be performed, without the necessity to use any other measuring instrument.
-
A2PATS® Products -
Textron Systems
Our A2PATS Family of Products are electromagnetic environment simulators built upon Textron Systems' open-architecture direct digital synthesizer technology, coupled with our proven user interface. Our easily programmable, plug-and-play modular architecture uses identical, phase-coherent, direct digital Synthetic Stimulus Instruments (SSIs) as the radio frequency (RF) source for all signals. These modular commercial RF Sources are easily configured in our commercial cabinets. Four standard configurations are available including single-cabinet, multi-cabinet, mini-A2PATS, and A2DSG™.The A2PATS Family consists of numerous commercial products including but not limited to A2PATS, A2DRI™, A2DSG and A2EOSTIM.
-
Networked Communication Solutions, LLC
Wi-In™, Online Wireless Sensor Monitoring from Networked Communications Solutions (NCS), is a network monitoring and notification system synced with NCS Wi-In™ wireless sensors. Our system provides for full configuration and customization at the local network, sensor and client-wide level. Wi-In™ will provide you total management of your notification parameters including the timing and frequency of alerts as well as the sequence of notification types and targets, such as phone calls, email, or SMS texts to one or more people. Our standard monitoring software is included with all sensors at no added cost—custom solutions are available at a reasonable cost.
-
CL-300 -
Schonstedt Instrument Co.
The NEW CL300 cable locating kit consists of a portable, holstered pipe & cable locator with an industry accepted 33kHz transmitted frequency. Comes standard with 512 Hz detection capability. With an added 512Hz transmitted device or traceable duct rodder the CL300 becomes the perfect tool for empty duct work locating. This instrument is capable of detecting all electrical, telecommunications and wire circuits—whether direct buried cables or those within conduits—using direct connect or close induction methods. This locator equipment features Auto & Manual adjustments for both transmitter power and receiver sensitivity to assist with a variety of locate work and congestion.Applications
-
SEM-600 -
Beijing KeHuan Century EMC Technology Co,.LTD
Broadband Electromagnetic Radiation Analyzer SEM-600 can accurately measure various complex electromagnetic environments. The probe covers all frequencies from low frequency to microwave radiation. It can measure electric field strength and magnetic field by equipping different types of probes. Intensity (magnetic induction) and power density, it is also equipped with ordinary probes and other weighted probes based on human safety standards.
-
GT-1000B -
Spanawave Corporation
The Spanawave GT-1000B Microwave Power Amplifier offers linear high-power amplification across multi-octave bands. It is ideal for testing in EMC, wireless communications applications and Defense EW systems. For EMI/EMC and standards laboratories, the GT-1000B with 100 MHz to 20 GHz frequency range allows broadband testing without band switching or swapping narrow band amplifiers resulting in faster and more accurate testing.
-
ALSAS 10U -
APREL, Inc.
Specific Absorption Rate (SAR) is a method for evaluating the exposure conditions of a wireless device to ensure global compliance to government standards. The ALSAS automated test solution allows for the evaluation of SAR both to optimize efficiency of a design and to ensure compliance with international safety requirements. Six independently controlled axis. Calculate multi-spot SAR and perform multi-cube analysis automatically. Covers frequency range of 30MHZ to 6GHz.
-
SGS100A -
Rohde & Schwarz GmbH & Co. KG
The R&S®SGS100A is an RF source designed to meet the requirements of automated test systems. It is available as a CW source or as a vector signal generator with an integrated I/Q modulator. With its frequency range of up to 12.75 GHz, the vector signal generation version covers the essential digital signals. The CW version can be used as a flexible local oscillator and for interference testing against mobile radio standards.
-
N5173B -
Keysight Technologies
Balance budget & performance to address parametric testing of microwave components & receiversPerform LO up conversion for microwave backhaul links or CW blocking for receiver testingMaximize test throughput with 600-s frequency switchingCharacterize microwave filters & amplifiers with the best combination of output power, low harmonics & full step attenuationUse as a high-stability system reference: the standard high-performance OCXO has an aging rate of 5x10-10 parts/day
